voyageoctave19

Choosing Upvc Window Replacement Hinges The process of selecting and fitting upvc window hinges for replacement isn't as difficult as you might imagine. Check that the hinges' arrows face the right way and determine the thickness of the hinge arms on the frame opening (13mm or 17mm). There are a variety of different kinds of hinges, each with its distinctive characteristics. This article will discuss some of the most common uPVC hinges and their advantages. Egress/Easy Clean Hinge These windows are an excellent choice for replacing or upgrading your fire escape safety windows because they can open to a full 90-degree angle. They can also be removed into an 'easy clean' position so that you can easily access the outside of windows to clean them without climbing a ladder or lean over at potentially dangerous angles. These heavy duty egress hinges are manufactured by Yale, one of the most well-known and trusted home security brands available today. They work with all types of uPVC side-hung windows. They can be moved into the easy-clean position by pressing an unassuming button, and then sliding the window sash over to one side. Once closed, the sash will automatically reset to its initial position. Both 13mm and 17mm are available. Depending on the size of your existing window we recommend using our Egress Selection Guide to determine which one is the best fit for your needs. The hinges are designed to work with standard side-hung frames, either uPVC or aluminium. The friction screw is used to adjust the resistance. This allows for easier opening of the window and reduces the possibility of a mishap during severe winds. They have been cycle tested to more than 30000 cycles and are in compliance with BBA/Secured by Design and British Standards approved BS EN 13126-6:2008. With no buttons or catches There are no buttons or catches. Nico Egress Easy Clean Friction Hinge is simple to use and provides a convenient solution to emergency egress as well as safe cleaning. Use the hinge retention clip located on the inside of the bottom corner. This will release both the catches on the top and bottom which will allow you to move the sash towards the clean position. Close the window when you are in the easy-cleaning position. This will set the hinges back to their Egress positions. Fire-Escape Hinge Fire Escape Hinges commonly referred to as “Easy Clean” hinges are used to replace side opening windows for egress (fire safety) reasons. These hinges permit an opening larger in the event of a fire. The building regulations state that this type of hinge should be placed in any habitable space with windows. The windows feature a friction stay that allows the windows to open up to 90 degrees. They also allow the opening sash to slide over the glass when it's opened and allows for easy cleaning without the need to use ladders. The hinges are simple to use and have no complicated buttons or catch mechanisms. They can be operated from inside of the house using a safe, simple lever. The hinges are manufactured in the UK by Cotswold and come complete with a child safety restrictor for day-to-day use that can be overridden with a hidden button giving you peace of mind that your children won't accidentally open the door too far. The stack heights are 13mm or 17mm. Take a measurement of the length of the side-hung window hinge that is attached to the frame. (See the article on measuring the size of Upvc window hinges). Select the proper size hinge from the options below. It is important to note that the measurement is taken from the part that fixes to the frame, not the sash. The real hinge length may be slightly shorter or larger based on the manufacturing process of your old windows. When choosing the width of the hinge the majority of frames made of upvc can accommodate the 13mm stack height, but if your old window frame is 17mm, you should select this option. You can also use the 4mm packer to compensate for the difference. All hinges come handed (1 left and one right). Screws aren't included with the hinges. If needed, they can be purchased separately. We recommend using our upvc window hinge repair screws. These are specially made to improve the performance of your hinges and allow them to function smoothly for longer. They have a reduced-friction design and an enhanced weather seal, which includes an encapsulated nylon reducer cap. Restricted Hinge There are instances when windows must fully open and this can be a problem with hinges that are standard. The restricted child safety friction hinges can help overcome this problem and are a great solution when ventilation is required but access to clean up or escape in the case of fire isn't possible. They work by restricting the amount of sash that can open, and allow for the control of this limitation with an option. They can be used for side- and top-hung windows. They are available in 13mm and 17mm stack heights. The Nico Restricted Egress Friction Hinge blends the advantages of a standard restrictor as well as an escape hinge to provide an efficient and easy way to comply with building regulations. It is available in 13mm and 17mm stack heights and can be used on both top and side opening uPVC window. It comes in two parts, with one hinge being the restricted egress, and the other the unrestricted. This allows one to be installed at the bottom while the other hinge is placed on top. These uPVC hinges are made to be used with windows that aren't able to be fully opened, such as a child's bedroom. The mechanism limits the extent to which the sash is able to open to 100mm for safety and re-engages when the window is closed. Like the other kinds of uPVC friction hinges, these can be used on all styles of windows and are ideal for those hard to reach windows above the ground level, three-storey flats or windows that normally require a ladder to access them. They can be complemented with our range of security features like hinge guards, protection plates for hinges or dog bolts to offer PAS 24 performance. It is essential to measure the hinge on your current window in order to get replacements that are the same size. This can be done by looking at the image gallery of the hinge and then deciding where you want it positioned. Top-hung hinges are limited on both sides, while side hung hinges are restricted only on one side. Standard Hinge Standard hinges have metal-to-metal contacts and do not require any additional parts to help reduce friction. It's available in a range of finishes, and is fire rated. To quickly determine the radius of hinges, lay it out flat and place a quarter and dime in two corners. If the dime fits better, the corner is rounded by ¼ inch; if the quarter fits better, it's rounded to 5/8 inch. Choosing the right type of hinge can make or break your door's appearance. It's essential to match the finish and style of your door with its hinges for a cohesive appearance that is both functional and visually appealing.